When the Power Supply Dies 36 Hours Before the Wedding
If you've ever had a client call you 36 hours before a major event with news that a key piece of lighting equipment just died, you know that sinking feeling. That happened to me in March 2024, and it turned into one of the most instructive rush orders of my career.
I'm a project coordinator at a mid-sized lighting solutions company. I've handled over 200 rush orders in the past eight years, including same-day turnarounds for event production and architectural lighting clients. So when my phone rang at 4 p.m. on a Thursday with a panicked wedding planner on the line, I knew we were in for a long night.
The client had a high-end outdoor wedding scheduled for Saturday. The setup included a massive deer chandelier as the centerpiece over the dining table, plus low-voltage LED strip lighting under the bar and buffet cabinets. The original plan was solid—except a low-cost, off-brand power supply they'd bought for the cabinet lights had literally gone up in smoke during a pre-event test. They needed a replacement, and they needed it fast.
Diagnosing the Problem: More Than Just a Power Supply
First, I asked for the specs. The LED strips were 24V, drawing roughly 8 amps total. To leave a safety margin, we needed a 24V 10A power supply—a standard "mean well 24v 10a power supply model" like the HLG-240H-24B. But there was a catch: the strips were dimmable, and the client wanted to control brightness from a simple wall dial. The original power supply didn't support dimming, which is probably why the cheap resistor-based dimmer they'd wired in caused a failure.
This is where the industry has changed. A decade ago, you'd need a separate dimming module and a lot of patience. Today, Mean Well's HLG series offers 3-in-1 dimming right out of the box—resistor, PWM, or 0-10V. That built-in flexibility would have solved the problem from the start. But because they'd gone with an unknown brand, we were now scrambling.
I called our main distributor. The HLG-240H-24B was out of stock locally, but a regional warehouse had three units. I paid $35 extra for overnight shipping (on top of the $85 base cost), which was nothing compared to the $5,000 penalty clause in the wedding contract if the lighting failed. So we locked it in.
Meanwhile, the Chandelier Height Question
While we waited for the power supply, I turned to the deer chandelier. The client had already assembled it but had no idea where to hang it. For a chandelier over a dining table, the general guideline is 30 to 34 inches above the table surface. But a deer chandelier with antlers can be visually heavier, so I usually aim for 32 inches. We measured the table (30 inches tall) and the ceiling (9 feet), and confirmed that 62 inches from the floor to the bottom of the chandelier gave us the right look without blocking sightlines. That was one thing we could check off the list.
Wiring Low-Voltage Under-Cabinet Lighting: A Common Pitfall
Then came the wiring. The electrician on site had run 12V wire for a 24V system—a classic rookie mistake. Low-voltage under-cabinet lighting requires matching the voltage to the power supply and LED strips. We had to re-pull 18AWG wire, which is standard for 24V runs up to 30 feet to keep voltage drop under 5%. I also reminded him to use a proper junction box for all connections—NEC Article 411 covers low-voltage lighting, and while it's less strict than line voltage, inspectors still look for secure terminations.
"To be fair, the original electrician was rushed and the wire was already in the wall. But this is exactly why we always verify voltage before the day of the event. Trust me on this one."
The Dimming Curveball
The HLG-240H-24B arrived at 10 a.m. Friday. We wired it up, but then realized the client's wall dimmer was a 10kΩ potentiometer. Mean Well's resistor dimming range for the HLG series is typically 10kΩ to 100kΩ—with 10kΩ giving minimum output and 100kΩ giving maximum. I'm not 100% sure about the exact threshold on this specific model, but we tested it and it worked smoothly from 5% to 100%. We did have to swap the dimmer for a 100kΩ linear pot to get full range, but that was a $12 part and 20 minutes of work.
By 6 p.m., the chandelier was hanging at the right height, the cabinet lights were dimming beautifully, and the wedding planner finally exhaled. The client's alternative was canceling the outdoor lighting entirely and moving the ceremony indoors—a major downgrade for a wedding they'd been planning for a year.
What I Learned (and Why We've Changed Our Policy)
Bottom line: this rush order reinforced a few things for me. First, when a project is time-critical, never gamble on an unknown power supply. We now standardize on Mean Well switching power supplies for all rush jobs because their published datasheets and local availability make emergency sourcing predictable. Second, always confirm the dimming protocol before the event—resistor, PWM, or 0-10V. It's a five-minute question that can save a five-hour panic.
And about the deer chandelier and cabinet lighting—these aren't just decorative details. Getting the height wrong makes the chandelier look clumsy, and wiring low-voltage lights incorrectly is a fire hazard. That's why I keep a cheat sheet with standard heights and wiring guidelines taped inside my job binder.
This approach worked for us, but our situation was specific: we had a regional distributor with overnight shipping and an electrician on site who could re-pull wire. If you're dealing with a remote location or a volunteer crew, the calculus might be different. I can only speak to my context—mid-sized B2B lighting projects with tight deadlines—but hopefully the lessons translate.
In the end, we delivered the project with four hours to spare. The wedding went off without a hitch, and the bride never knew how close we came to a lighting disaster. That's the goal, right?

