-
Step 1 — Confirm You Actually Need a Lighting Contactor (Not a Switch)
-
Step 2 — Pressure-Test Your Sensing Needs Before You Buy
-
Step 3 — Know What You're Actually Buying (Canless Recessed vs. Surface)
-
Step 4 — Check the Hanging Point for Chandeliers (Every Single Time)
-
Step 5 — Review Your Surge Protection Scope
-
Step 6 — Write a Commissioning Checklist Before You Sign the PO
-
What I'd Watch Out For (From Experience)
This is the checklist I run before signing off on any lighting procurement order—whether it's a 40-fixture office retrofit or a 200-fixture warehouse re-lamp. I built it after six years of documented mistakes, including one order in 2021 that cost $1,100 in non-returnable parts and pushed a project back three weeks.
This checklist is for facilities managers, procurement leads, and project coordinators who have to specify or approve lighting purchases—not the electricians who install them. If you're a licensed contractor, half of this will be old news. The other half might still catch something.
Total prep time: roughly 30 minutes. Six steps.
Step 1 — Confirm You Actually Need a Lighting Contactor (Not a Switch)
This one sounds obvious. It isn't. In 2020, I approved a batch of standard 20A lighting switches for a parking garage retrofit. The contractor installed them, and six weeks later I got a call: two of the switches had welded closed. The fixture load—14 high-bay LEDs per circuit—exceeded what those switches were rated for continuous duty.
That error cost $680 in replacement switches plus an awkward call to the client. Like most beginners, I assumed a 20A rating meant it could handle anything up to 20A continuously. It doesn't.
Lighting contactors like Eaton's—or equivalent—are what you actually need when:
- Each circuit drives more than 10 fixtures
- You're switching large LED, fluorescent, or HID loads
- You're switching from a control side rather than just locally
Eaton's lighting contactors come in mechanically held (quiet, for lobbies) and electrically held (general-purpose) versions. If you're doing corridor, parking-garage, or industrial work, spec the models with a manual override—trust me, maintenance will thank you.
Checkpoint: Count fixtures per circuit. Compare to the switch's label rating. If the label says "tungsten" or "incandescent," you need a contactor.
Step 2 — Pressure-Test Your Sensing Needs Before You Buy
This one really stung. In 2022, I spec'd standard ambient-temperature sensors for a transformer room. They were rated for -10°C to 40°C operating. That room hits 55°C in summer. Two sensors died within eight weeks.
Eaton's transmission temperature sensors—the models used for monitoring transformer and switchgear temperatures—come in multiple environment and equipment ratings. I put an ambient-grade model where I needed an equipment-grade one. I still kick myself for not asking about the operating range before I clicked 'buy.'
So before you spec any sensor:
- Measure the actual install environment on the hottest day you can find
- Read the sensor datasheet for operating range, not storage range (easy to mix up)
- Consider redundancy if the reading will drive control decisions
Checkpoint: Cross-check the datasheet's operating range against your measured (or estimated) ambient temperature. If it's within 5°C of the limit, size up.
Step 3 — Know What You're Actually Buying (Canless Recessed vs. Surface)
Here's where people mix up fixture types and end up paying for it.
What is canless recessed lighting? Simply put, it's a recessed fixture with a thin-profile LED wafer or module and a very narrow or invisible trim—often color-matched or same-material as the ceiling. It looks like a glowing hole cut directly into the ceiling. You'll see it in modern offices, hotel lobbies, and high-end residential.
It looks great. But it has installation constraints:
- Typically needs 3 to 5 inches of ceiling cavity depth (varies by model)
- Some models require a larger cutout opening than you'd expect, for heat dissipation
- They don't play well with acoustic or fire-rated ceilings unless specifically rated
In 2021, I spec'd a 4-inch-depth canless fixture for a ceiling that only had 3.5 inches of cavity (old metal furring system). The installers had to cut and rework it on site, waited weeks for a restock, and I got a $1,100 rework bill (note to self: stop guessing ceiling cavity depth).
Checkpoint: Measure ceiling cavity depth first—pop an existing fixture or pull the ceiling spec. Then match to the datasheet's minimum ceiling thickness with a 20% buffer.
Step 4 — Check the Hanging Point for Chandeliers (Every Single Time)
If you're buying decorative lighting for commercial or hospitality spaces, rectangular chandeliers and rustic chandelier designs are common—but they're heavy and often unbalanced. I don't do hanging-point load calcs myself. I'm not a structural engineer, so that's a question for one. But I've learned to ask the right questions before I sign off.
My most embarrassing mistake: I approved a 28-lb rectangular rustic chandelier hung from a drywall drop ceiling with standard toggle bolts. Two months later, the drywall anchors pulled through on one end. It dropped onto an empty table below (thankfully nobody was sitting there).
After this, we started requiring structural verification before install:
- Get the fixture's shipping weight, not just the spec sheet's net weight
- Verify the mounting hardware's rated capacity against that weight
- If mounting to drywall or a drop ceiling, map out the joists before you pick anchors
- A rectangular or multi-point fixture usually needs at least two mounting points
Checkpoint: Ask the electrical contractor to pull structural drawings before installation day. It's a 15-minute check that prevents a lawsuit.
Step 5 — Review Your Surge Protection Scope
Most people skip this step. Please don't.
Surge protection for lighting controls isn't just about lightning—commercial buildings generate their own surges from HVAC equipment, elevator motors, and switching operations. In 2023, a project had an unprotected lighting control panel that blew after an HVAC compressor kicked on. That cost $1,600 to replace.
If you're including surge protection in your lighting circuit:
- Check at the panel level—do you need a service-entrance SPD?
- Check at the control level—DIN-rail mounted SPDs protect lighting relays/contactors
- If you're using Eaton's lighting control systems, verify compatibility
This is where I get conservative. I'm not a surge protection engineer, so I don't make these calls on my own. I pull in the electrical contractor or call Eaton's tech support. They ask questions I wouldn't have thought of.
Checkpoint: List all equipment on the project that switches large inductive loads (motors, HVAC, elevators). If that list is non-empty, you need at least one surge protective device in the system.
Step 6 — Write a Commissioning Checklist Before You Sign the PO
This is the single most important habit I picked up—and it took me four years to adopt.
Before you send the purchase order, write down how you'll test and accept the lighting system:
- Does each circuit respond to its intended control?
- Are contactors holding properly (listen for chatter)?
- Are there sensor dead zones or triggers that fire too early?
- Does the override work?
- Do all fixtures light, with no flicker or drivers overheating?
In 2022, we installed a lighting control system, but the acceptance test was basically "looks bright enough." Three months later, we learned that three sensors had been set to "always on." Nobody knew how to reconfigure them until page 47 of the tech manual.
Checkpoint: Write your acceptance test before the PO goes out. Every test should be a 30-second procedure. Then confirm with the vendor that their commissioning documentation matches your test.
What I'd Watch Out For (From Experience)
Mistake 1: Checking switch ratings by count, not by load type. A 20A tungsten-rated switch won't handle high-inrush LED loads. Check the datasheet's continuous-load rating.
Mistake 2: Using storage temperature as operating temperature. They're different. Read carefully.
Mistake 3: Guessing ceiling cavity depth. Don't. Measure it.
Mistake 4: One mounting point for a multi-point fixture. Rectangular and rustic chandeliers typically need two.
Mistake 5: Skipping surge protection scope. It's not just about lightning—it's about the equipment you're already installing.
Mistake 6: Verbal acceptance. Write it down. If it isn't documented, it didn't happen (ugh, I learned this one twice).
Prices and lead times referenced here were accurate as of January 2025. Electrical supply chains move fast, so verify current pricing and availability before you budget.
There's something satisfying about a lighting project that just works—no callbacks, no ruined schedule, no angry calls from the client. It takes 30 minutes of prep and a checklist you'll actually use. That's the whole point.

